Buying guide

How to Measure Range Hood Size

Updated on · By the Got Vents team

Measure the stove's width first and match the hood to it: a hood should span the full cooktop or extend a few inches past each side. Then measure cabinet depth and the space between the cooktop and any cabinet above, so the hood fits and vents freely.

On this page (10 sections)
  1. How do you measure the stove width for a range hood?
  2. How wide should the hood be compared with the stove?
  3. How do you measure the depth of the hood and cabinets?
  4. How do you measure the space above the cooktop?
  5. How do you size airflow to match the hood and stove?
  6. How do you measure the vent and duct path?
  7. Which type of hood fits your measurements?
  8. How do you measure the cabinet opening for an under-cabinet hood?
  9. What mistakes should you avoid when measuring range hood size?
  10. The bottom line on measuring for a range hood

To measure range hood size, start with the stove width. A hood should match the cooktop's full width or run a few inches wider on each side.

Then measure cabinet depth and the clearance between the cooktop and the cabinet above so the hood fits and vents properly.

Width gets you close. Depth, height and airflow decide whether the hood actually works in your kitchen.

This guide walks through each measurement in order, so you can size a hood once and buy with confidence.

How do you measure the stove width for a range hood?

Measure your stove's full width across the top, from edge to edge. That number is the starting point for hood width, and most standard hoods come in 30-inch and 36-inch sizes to match common ranges.

Use a tape measure across the front edge of the cooktop, not the countertop or the cabinet run. A slide-in range and a freestanding range of the same nominal size can differ by a fraction of an inch at the trim.

Write the measurement down in inches. If your stove is a nonstandard width, you'll be shopping outside the common 30 and 36 inch options.

For a full rundown of matching hood width to stove size, see our guide on what size range hood you need for your stove.

Standard hood widths and what they fit

Hood widthTypical stove widthNotes
24 in20 to 24 inCompact and apartment kitchens
30 in30 inThe most common size in US kitchens
36 in36 inWider ranges and pro-style cooktops
42 in and up36 to 48 inLarge or custom kitchens

A 30-inch hood over a 30-inch stove is the baseline. Going to a 36-inch hood over a 30-inch stove adds capture area if the cabinets allow it.

Pick a size the cabinet opening can take before you fall in love with a wider hood. That way the width you measured for the stove stays tied to a model your kitchen can actually hold, and you won't order a hood that has to be sent back.

How wide should the hood be compared with the stove?

The hood should be at least as wide as the stove and ideally a few inches wider. A hood that's narrower than the cooktop lets smoke and steam escape around the edges.

The extra width matters most on gas ranges and high-heat cooking. Steam rises and spreads as it climbs, so a hood that covers the full burner footprint catches more of it.

Many installers aim for 3 inches of overhang on each side, though the hood's instructions set the real rule.

Check the space between the stove and the walls or side cabinets. A wider hood can collide with a side cabinet or a window ledge.

Measure that gap before you size up.

If your stove sits tight between cabinets, a hood that matches the stove width exactly is the safe choice. Our walkthrough on measuring for an under cabinet range hood covers how to fit the hood inside an existing cabinet opening.

Note the width of that opening next to your stove width, because the smaller of the two numbers is your real limit. A stove that's 30 inches wide still can't take a 30-inch hood if the cabinet opening is narrower than that.

How do you measure the depth of the hood and cabinets?

Measure cabinet depth and match it to the hood's depth. Standard base cabinets run about 24 inches deep, and a hood that's too deep crowds the cooktop while one that's too shallow loses capture.

Measure from the wall to the front edge of the cabinet. Then compare that with the hood depth.

Wall-mounted and under-cabinet hoods usually land in the 18 to 24 inch range, while island hoods can run larger.

A hood that sticks out past the cabinet edge looks wrong and can block headroom. One that's set too far back leaves smoke rolling forward before the fan catches it.

Check the hood's depth figure against your cabinet before ordering.

The Broan-NuTone 413004 measures 30 inches wide, 17.5 inches deep and 6 inches high. That depth figure is the one to compare against your cabinet run, since the front edge needs to sit flush with or just inside the cabinet face.

Write down your cabinet depth next to that number so you can see the gap at a glance.

Depth also ties into the filter you'll be changing. A hood with a grease filter needs enough front clearance for the filter to slide out, so leave a hand's width in front of the cabinet edge when you plan the fit.

Our guide on how deep a range hood should be explains the trade-off between depth and capture in more detail.

How do you measure the space above the cooktop?

Measure from the cooking surface to the underside of the cabinet above. That gap decides how much room you have for the hood and whether it meets the clearance your model requires.

Electric cooktops typically need about 24 inches of clearance. Gas cooktops usually need about 30 inches.

The hood's own instructions take priority, and local codes can be stricter.

Measure from the top of the burner grates or the smooth cooktop surface, not from the counter. A hood installed too low can be a fire risk and can block your view of the back burners.

One installed too high lets smoke spread before the fan pulls it in.

Broan-NuTone specifies an 18 inch minimum above the cooktop for the 413004. That's its own figure, so follow the model you buy rather than a generic number.

Check the gap against your cabinet base before you commit. If your measured gap leaves less than the model asks for, you either raise the cabinet, change to a shallower hood, or choose a different model.

How do you size airflow to match the hood and stove?

Airflow should rise with the burner count and the hood's capture area. A hood that's sized right in width but weak in airflow still leaves smoke behind.

A rough rule is 100 cubic feet per minute for every 10,000 BTUs of burner output. A typical gas range has four burners and a combined output in the tens of thousands of BTUs, so a hood in the 200 to 400 CFM range is common for home cooking.

Pick up the stove's BTU rating from its label or manual.

Ducted hoods move more air than ductless ones. Ductless models pass air through a charcoal filter and return it to the kitchen, so their real-world pull is lower.

The Broan-NuTone 413004 moves 100 CFM, which suits light cooking over an electric or low-output gas range.

Airflow is only half the story on a ductless hood. The charcoal filter inside it is what traps odors and smoke particles before the air comes back into the room.

The Broan-NuTone 413004 uses a replaceable charcoal filter, and Broan-NuTone calls that out as the part that keeps grease capture up over time. If you skip the filter change, the hood keeps running but stops cleaning the air.

If you're weighing the two paths, our comparison of convertible vs ducted range hoods explains what changes in airflow and installation.

When to step up the airflow

Choose more airflow when you cook with high heat often or use a large gas range. A hood with more CFM also needs a duct that can carry it and a makeup air plan in tight homes.

Check both before sizing up.

Airflow and filter maintenance travel together. A hood that runs at a modest 100 CFM like the Broan-NuTone 413004 relies on its charcoal filter to keep returning clean air, so the filter change is part of the airflow plan, not an afterthought.

Add a note to your measurements for when the filter should be swapped.

How do you measure the vent and duct path?

Trace the duct route from the hood's outlet to the outside before you pick a model. The path decides whether you need a vertical or horizontal outlet and how long the run will be.

Start at the wall or cabinet above the stove. Note whether the duct exits straight up through the roof or turns sideways through a wall.

Count every elbow, since each one costs airflow.

Measure the distance from the hood's outlet to the outside cap. Long runs and sharp turns reduce the fan's pull.

A ductless hood skips this step, which is why it's the easy fit for kitchens with no duct path.

Duct size and the outlet position

Most residential hoods use a 6-inch round or 3.25 by 10 inch rectangular duct. Match the hood's outlet to the duct you have or plan to run.

Measure the outlet size on the model you want, then compare it with your wall or roof cap.

Write down the outlet position too, since a top outlet and a rear outlet sit in different places on the cabinet. A rear outlet needs a clear run behind the hood to the wall, while a top outlet needs space above the cabinet.

If your measured path only allows one of the two, that's another limit on which model fits.

Which type of hood fits your measurements?

Let the measurements decide the type, not the other way around. The cabinet, wall and duct space you've measured point to one type of hood over another.

  • Under-cabinet hoods mount beneath the upper cabinet and suit kitchens with cabinets over the stove. Measure the cabinet width and depth to find the largest hood that fits.
  • Wall-mounted hoods hang from the wall and need open wall space above the cooktop. Measure the wall width and the chimney height you can allow.
  • Island hoods hang over a cooktop set in an island. Measure the ceiling height and the duct path through the ceiling.
  • Ductless hoods return filtered air to the room and skip the duct. They suit rentals and kitchens with no vent path, though their airflow is limited.

The Broan-NuTone 413004 is an under-cabinet ductless insert at 30 inches wide and 17.5 inches deep. It mounts beneath the cabinet, uses a push-button rocker switch to run its two-speed fan and light separately, and its charcoal filter needs replacing to keep grease capture up.

That last point belongs in your plan, because a ductless hood's cleaning depends on a fresh filter. You can see how convertible vs ducted hoods differ in venting before you choose.

How do you measure the cabinet opening for an under-cabinet hood?

Measure the cabinet opening's width, depth and height, then allow for the hood's body and the space it needs to sit flush. The opening sets the ceiling on hood size for this type.

Start with the width between the cabinet side panels. A 30 inch opening takes a 30 inch hood with a little room to spare.

Then measure the depth from the wall to the front edge of the cabinet.

Check the height from the cabinet base to the underside of the cabinet's top shelf or the bottom of the next cabinet. The hood body needs to fit under the cabinet without hitting shelves or the cabinet door swing.

Leave room for the fan, wiring and the hood's mounting screws. Our under-cabinet measuring walkthrough covers the full sequence, and the range hood size guide ties cabinet width back to stove width.

Checking the cabinet's mounting surface

Measure the cabinet base's flat area where the hood will attach. A narrow or uneven base can limit the hood's mounting options.

Also note where the power outlet sits so the cord can reach. On the Broan-NuTone 413004, the body sits 6 inches high under the cabinet, so the base needs enough flat surface to take the mounting screws and leave the push-button controls reachable from the front.

The hood's light takes a bulb up to 75 watts and has its own switch, so leave room to change that bulb from below without pulling the unit out.

What mistakes should you avoid when measuring range hood size?

The most common mistake is measuring the countertop instead of the cooktop. The two can differ, and the cooktop width is what sets the hood width.

Other frequent errors:

  1. Forgetting the clearance above the cooking surface. A hood that's too low or too high changes how well it captures smoke.
  2. Measuring the cabinet opening without checking the hood's depth. A deep hood can block headroom and look out of place.
  3. Ignoring the duct path. A ducted hood needs a route to the outside, and a long run reduces airflow.
  4. Sizing airflow to the kitchen rather than the burners. A weak fan behind a wide hood still leaves smoke behind.
  5. Forgetting the filter and maintenance space. Grease filters and charcoal filters need room to slide out.

Check each number twice before you order. A tape measure and a notebook are all you need.

A quick second pass also catches the easy slip of reading the stove's model number as its width, so measure the trim itself rather than trusting the label.

The bottom line on measuring for a range hood

Measure the stove width first, then depth, mounting height, duct path and airflow. A hood that spans the cooktop or runs a few inches wider is the right starting size.

The cabinet and duct space set the limits on type and fit.

If you're still deciding on width, our guide on what size range hood do you need goes deeper into matching hoods to stove and kitchen size. For the venting decision, read up on convertible vs ducted range hoods, and check how deep a range hood should be before you fix the cabinet position.

Write down all five measurements before you shop. With width, depth, height, duct path and airflow in hand, you can size a range hood in one pass and skip the returns.

Frequently asked questions

Should a range hood be wider than the stove?

A hood that spans the full stove width is the minimum for most kitchens. Going a few inches wider on each side catches steam and smoke that drifts outward while you cook.

How much space do I need between the cooktop and the hood?

Electric cooktops usually need about 24 inches of clearance and gas cooktops about 30 inches, though the hood's own instructions take priority. Measure from the cooking surface to the lowest edge of the hood.

Can I install a 36-inch hood over a 30-inch stove?

Yes, if the cabinets and ceiling allow it. A 36-inch hood over a 30-inch stove gives extra capture on both sides and is a common upgrade in kitchens with room above.

How do I measure for a hood under existing cabinets?

Measure the cabinet run width and depth, the height from the cooktop to the cabinet base, and the duct or vent path. That tells you the largest hood the opening will take without cutting new cabinet space.